To everyone watching this video regarding the vacuum valve sensor. The vacuum valve sensor must not get any water inside where the diaphragm is operating or it will keep it in the on position. The diaphragm is a very sensitive rubber piece and water between the case and the diaphragm will keep it in a on position. It is recommended to put it in a enclosed container watertight. I found this out when I had the device setting on the outside of the car testing it and I decided to wash the inside of the engine area with the car in the off position and seen it working still. This vacuum valve was designed for a furnace in a dry environment and I recommend for everyone using one keep it dry.
Regarding the furnace vacuum diaphragm after a period of running the furnace vacuum diaphragm it is such a sensitive unit that a hole developed in the diaphragm causing a vacuum leak. This diaphragm on the furnace vacuum valve is a very thin film around the diaphragm plate inside. I found a company that manufactures vacuum switches designed for automobiles that should arrive at my door on November 12, 2008. When the automobile is on idle this is where the vacuum is at its highest point and if the diaphragm can not handle the intense vacuum it will develop a whole in the diaphragm membrane. I received my O2 sensor box and using it by it’s self on my automobile I have improved my gas mileage from 30-32 Highway to 36-39 Highway until the old furnace diaphragm got a hole in it and then I seen a reduction. I will being doing another test when the new vacuum switch that is designed for the automobile arrived and I would do another O2 sensor box road test. The O2 sensor box controls the manifold O2 sensor and the catalytic converter O2 sensor on the exhaust system. After running a test on the O2 sensor box and showing it on video. I will be adding the hydrogen & oxygen generator back onto the car and showing them running together with additional improvements to the generator because of the winner season arriving in Michigan.
Beware of other individuals selling hydrogen oxygen machines without safety being a number one issue. As you see in my experimental videos, I keep speaking about safety over and over because it is very important to everyone dealing with HHO gas. HHO gas is extremely explosive and if a Manufacturer cannot show you a video demonstrating their safeties beware of what you buy. This video you are watching shows my complete system on the vehicle. Before it was put on the car all testing was done off the car assuring you that the safeties do work as I state. Watch the other videos that are posted close to the date of posting of this video for all the tests that were done. Nothing is 100% but it is better than nothing.
Duration : 0:10:47
September 6th, 2009 at 10:30 am
can table salt be …
can table salt be used to induce electrolysis, some guy in FL. used radio waves to ignite salt water
September 6th, 2009 at 10:30 am
not in my country …
not in my country anyway.
September 6th, 2009 at 10:30 am
i don’t understand …
i don’t understand why you have to make it so complax.
September 6th, 2009 at 10:30 am
you can buy at the …
you can buy at the store
September 6th, 2009 at 10:30 am
I will be selling …
I will be selling the vacuum relay switches for any application for any engine size. Please be patient I have a lot going on this summer and I will be selling HHO devices and accessories. I will be selling HHO welders, HHO cooking stoves, and many other devices.
September 6th, 2009 at 10:30 am
Where can I buy …
Where can I buy vacuum switches? can you recomend any company website? I need one for a 12VAC system scooter. my cell needs to use battery power directly, but no relay is applicable… except a vacuum activated control switch… Help!
September 6th, 2009 at 10:30 am
Non viene …
Non viene commercializzaro nulla del genere perchè conviene ai petrolieri che le macchine vadano a benzina!
September 6th, 2009 at 10:30 am
you can also use …
you can also use baking soda for electrolytes
September 6th, 2009 at 10:30 am
To: Cambu1226
“YES” …
To: Cambu1226
“YES” —It is kool-aid for electrolytes
September 6th, 2009 at 10:30 am
is the kool-aid for …
is the kool-aid for electrolytes?
September 6th, 2009 at 10:30 am
if h burns 40,000 …
if h burns 40,000 faster then gas adding a good mix without advancen the timing.I guess what Im trying to say wouldnt make the engine work harder
September 6th, 2009 at 10:30 am
My electronic …
My electronic device has arrived and I have tested it with the HHO and with out the HHO and have seen improvements both ways. I have had some personal issues come up in my life that put me on hold for approximately 2 to 3 weeks. I will be putting new videos on the Internet shortly demonstrating the device for everyone’s review.
September 6th, 2009 at 10:30 am
So does this run …
So does this run only on HHO gas or is it a hybrid and if it runs only on HHO gas how do I go about converting my car?
September 6th, 2009 at 10:30 am
Nice system! You …
Nice system! You have done your home work. A+. Very neat and well explained.
September 6th, 2009 at 10:30 am
excellent work!! …
excellent work!! great video!! =D
September 6th, 2009 at 10:30 am
that look …
that look interesting, would u mind showing some diagrm ?
September 6th, 2009 at 10:30 am
I have received …
I have received some mileage increase and then the car computer from the factory fights the HHO gas and brings it down to normal standards. I have ordered a electronic device to alter the O2 sensor and the map sensor that should arrive today September 13, 2008. Once it is on the car I will do it new video showing the new readings.
September 6th, 2009 at 10:30 am
Great and neat work …
Great and neat work !
did you get mileage improvements?
how much HHO LPM did you get ?
October 1st, 2009 at 1:11 am
You are right, Safety is the number one issue while purchasing hydrogen, oxygen machines or dealing with any inflammable gas.